![]() ![]() If the lock is muted, you will not hear beeping during programming, normal operation, low battery indicators, or system alerts.ģ. You can set the Auto-Lock time delay between 10 and 99 seconds. Repeat steps 1 and 2 to enable or disable Auto-Lock again. The Auto-Lock feature automatically re-locks your door 30 seconds after unlocking. ![]() Kwikset keypad deadbolt code#If all User Codes are deleted, the lock can only be operated by the key and turnpiece until a new User Code is added. Repeat steps 1 and 2 to enable or disable the codes again. If User Codes are disabled (example: when you go on vacation), the lock can only be operated by the key and turnpiece until they are enabled again.ģ. Test the code: While your door is open, lock it and enter the User Code to make sure it no longer unlocks the door.Ī one-time user code may be used only once, and then it will be deleted immediately after use. ![]() Enter the User Code you wish to delete.ĥ. It is recommended that you delete this code.ģ. ![]() The lock is pre-programmed with a default User Code of 1-2-3-4. Test the code: While your door is open, lock it and enter your new User Code to make sure it unlocks the door. Do not program a User Code that is the same as your PC.ģ. It must be between 4 and 10 digits.Ī total of 6 User Codes (and a temporary one-time User Code) may be programmed. It is recommended that you change it to a code of your own.ģ. It is an added security feature that is used to set up all functions. The Programming Code (PC) will not unlock your door. Note: If the lock is muted, you will not hear the lock beeping. If unsuccessful, the Kwikset button will flash red 3 times and you will hear 3 beeps. IMPORTANT: Before any programming sequence, make sure that your door is open and unlocked.įor all programming sequences below, success is indicated when the Kwikset button flashes green 2 times and you hear 2 beeps. It is recommended that you replace the default Programming Code and default User Code with codes of your own. The latch bolt will extend to lock.ĭ Enter the default User Code (1-2-3-4), then press the Kwikset button. If unsuccessful, the Kwikset button will flash red 3 times, and you will hear 3 beeps.Ĭ If successful, press the Kwikset button. I Reinstall the battery cover and make sure the latch is still in the unlocked position.Ī While the door is OPEN and UNLOCKED, enter the following code to teach the lock the orientation of the door:ī If successful, the Kwikset button will flash green 2 times and you will hear 2 beeps. H Secure the interior assembly with the supplied screws. G Test the turnpiece for smooth rotation. Kwikset keypad deadbolt install#For best results, use new, non-rechargeable Alkaline batteries only.Ĭ Press and hold the Reset button on the interior assembly for 5 seconds, until you hear 3 beeps.ĭ Align the colored edges of the connectors and ensure a tight cable connection.Į IMPORTANT: Rotate the turnpiece AWAY from the door edge.į Make sure the torque blade is still in the horizontal position and install the interior assembly. I Remove the key and make sure the latch bolt is still in the unlocked position.ī Load 4 AA batteries into the interior assembly. H Insert the key and test the latch for smooth operation. G Secure the mounting plate with the supplied screws. Proceed to step 4.Ī Install the cylinder into the exterior assembly.Ĭ IMPORTANT: Make sure the latch is fully retracted (in the unlocked position).ĭ IMPORTANT: Make sure the torque blade is in the horizontal position.Į Insert the torque blade through the horizontal slot of the cross-shaped hole.į Push the torque blade through the center hole in the mounting plate and send the cable through the bottom hole. What is the diameter of the hole in the door? Prepare keypad and mounting plate (only for doors with smaller holes) Is the cross-shaped hole centered in the door hole?ĭ Make sure the latch bolt is fully retracted (in the unlocked position). Consult the deadbolt drilling instructions at B Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).Ĭ Measure to confirm that the hole in the door edge is 1″ (25 mm).ĭ Measure to confirm that the door is either 1-3/8″ or 1-3/4″ (35 mm or 44 mm) thick.Ī Hold the latch in front of the door hole, with the latch face flush against the door edge. Note: Additional door preparation may be required for doors with 1-1/2″ (38 mm) holes. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |